| DC Voltage |
| |
400.0 mV
4.000, 40.00, 400.0 V
600 V
NMRR:
CMRR:
Input Impedance
Transient protection: |
±(0.03% + 4 dgt)
±(0.5% + 3 dgt)
±(1.0% + 4 dgt)
>50 dB@DC, 50/60 Hz
>120 dB@DC, 50/60 Hz, Rs=1 kHz
10 MΩ, 30 pF nominal (1000 MΩ for 400.0 mV range)
6.5 kV (1.2/50 µs surge) |
| AC Voltage (50 Hz ~ 500 Hz) |
| |
4.000, 40.00, 400.0 V
600 V
CMRR:
Maximum crest factor:
Input impedance:
Transient protection:
ACD-10 PLUS: |
±(1.5% + 5 dgt)
±(2.0% + 5 dgt)
>60 dB @ DC to 60 Hz, Rs=1 kΩ
less than 1.75:1 at full scale & less than 3.5:1 at half scale
10 MΩ, 30 pF nominal
6.5 kV (1.2/50 µs surge)
Average sensing |
| AC Current |
| |
40.00, 400.0, 600 A
Overload proctections:
ACD-10 PLUS |
±(1.5% + 8 dgt)1,2,3
ACA Clamp-on jaws:600 A rms continuous
Average sensing
|
1) Max induced error from adjacent current carrying conductor:
0.05 A
2) Specified accuracy is from 1% to 100% of range and for measurements made at the jaw
center. When the conductor is not positioned at the jaw center, position errors introduced are: Add
2% to specified accuracy for measurements made BEYOND jaw marking lines (toward jaw opening).
3) Add 8 digits to specified accuracy @ reading < 10% of range. |
| Resistance |
| |
400.0 Ω
4.000, 40.00, 400.0 kΩ
4.000 MΩ
40.00 MΩ
Open circuit voltage:
Transient protection:
|
±(0.8% + 8 dgt)
±(0.6% + 4 dgt)
±(1.0% + 4 dgt)
±(2.0% + 4 dgt)
0.4 VDC typical
6.5 kV (1.2/50 µs surge) |
| Frequency |
400.0 mVac
4.000 Vac
4.000, 40.00 Vac
400.0 Vac
600 Vac
400.0 Aac |
0 Hz ~ 2 kHz
5 Hz ~ 5 kHz
5 Hz ~ 100 kHz
5 Hz ~ 10 kHz
5 Hz ~ 5 kHz
40 Hz ~ 400 Hz |
±(0.5% + 4 dgt)
±(0.5% + 4 dgt)
±(0.5% + 4 dgt)
±(0.5% + 4 dgt)
±(0.5% + 4 dgt)
±(0.5% + 4 dgt) |
| Display counts: |
5000 |
| Resolution: |
0.001 Hz |
| Overload protection: |
ACA Clamp-on jaws: AC 600 A rms continuous |
| Transient protection: |
VAC input jacks: 6.5 kV (1.2/50 µs surge) |
| Capacitance |
| |
Range1 |
Accuracy2,3 |
| |
500.0 nF, 5.000 µF
50.00 µF, 500.0 µF, 3000 µF |
±(3.5% + 6 dgt) |
1) Additional 50.00 nF range accuracy is not specified
2) Accuracies with film capacitor or better
3) Specified with battery voltage above 2.8 V (approx. half full battery.)
Accuracy decreases gradually to 12% at low battery warning voltage of approximately 2.4 V |
| Transient protection: |
6.5 kV (1.2/50 µs surge) |
| Audible continuity tester |
| Audible indication: |
between 10 Ω and 120 Ω |
| Transient protection: |
6.5 kV (1.2/50 µs surge) |
Max hold* (where applicable)
Specified accuracy ± 50
digits for changes > 25 ms in duration |
